What to do if BitLocker fails to encrypt drive

Did you know that Microsoft’s BitLocker encryption software can be used to encrypt your entire hard disk drive? The software is included with Windows 10 Professional, Windows 8.1 and Windows 7 Enterprise, and can also be used with Windows Server 2008, 2008 R2 and 2012. There are two ways to encrypt a drive: you can opt to encrypt the entire drive or just the used portions of the drive. Once encrypted, you can access the drive only when you enter a password, and the encryption key is stored on a USB drive or in the TPM chip on the motherboard.

BitLocker is an encryption technology developed by Microsoft, and is included with Windows 7 Ultimate and Enterprise editions. BitLocker protects your data by encrypting it, which means that only people who have a BitLocker recovery key can see the data you have stored on your computer. If you are using a computer that has BitLocker encryption and it fails, you may be able to repair it using the BitLocker recovery console.

  1. Start the command prompt as administrator, type diskpart, and press Enter.
  2. Type list disk to display the list of all drives
  3. Enter Select Drive # (where # is the problematic drive).  Press the Enter key.
  4. Type clean and press Enter.
  5. Wait until the disc is erased. It is now time to create a new section.
  6. Type create partition primary and press Enter
  7. Enter a target letter = #. (Again, # is the letter you want to use).
  8. Format the partition by typing format fs=ntfs quick. Press the Enter key.

2. Modification of safety ship settings

According to reports, this problem seems to occur on computers with Intel PTT security chips and when using certain settings.

When the problem occurred, BitLocker Drive Encryption was using TPM and PINs, and the Allow BitLocker without compatible TPM option was disabled. In addition, the machines operating system was installed in the BIOS and not the UEFI.

Here are the general steps to follow. Note that these may be different on your device.

  1. Start the computer and open the BIOS setup.
  2. Click on the Security tab and select Security Chip Settings.
  3. Select the Discrete TPM option.
  4. Navigate to Remove Security Chip and save your changes.
  5. Restart the unit, log on and enter the PIN code. Check if the problem persists.

If you want to undo this action, you need to replace the firmware boot option with a UEFI boot. Sometimes a reinstallation of the operating system may also be required.

Message: If you cannot find a solution, we recommend you to switch to Folder Lock, a powerful encryption program.

Comprehensive security options include copying encrypted files to USB drives, CDs and DVDs, and even email attachments, as well as the ability to upload encrypted files to a cloud server.

⇒ Get the folder lock

3. Enable BitLocker without compatible TPM

  1. Open Run from the Start button, type gpedit.msc and click OK.
  2. The local Group Policy Editor opens.
  3. In Computer Configuration, click Administrative Templates, and then click Windows Components.
  4. Select BitLocker Drive.
  5. Go to Encryption and then to Operating System Disks.Bitlocker Operating System Disks
  6. Double-click Startup with additional authentication required.
  7. In the new window, select Enabled and Allow BitLocker without compatible TPM (requires a password or boot key on a USB flash drive).
  8. Save the changes by clicking the Apply button.
  9. Now try to encrypt the disk with BitLocker.

4. Delete TPM (Trusted Platform Module)

Before you start removing TPM settings, you should have backed up your computer as described in the first solution. This method may result in data loss.

  1. Open Run from the Start button, type tpm.msc, and press Enter.
  2. A new administration console opens.
  3. In the Action tab on the right, click Remove TPM.TPM Trusted Platform Module
  4. In the Remove TPM Security Hardware window, the simplest solution is to check the I don’t have an owner password box and click OK.
  5. You will be prompted to reboot. You will see that you have to press a key (usually F10) to remove the TPM.
  6. After the system reboots, you will be asked to press a key (usually F10) to activate the TPM. Press this button.
  7. This will start the TPM Setup Wizard, where you must enter the TPM owner’s password.

5. Changing USB device settings in BIOS

  1. Call up the BIOS setup program.
  2. Go to Advanced and then to Peripheral Device Configuration.
  3. Access the USB host controller and USB devices.
  4. The settings of the USB device should be all.

This solution is used when BitLocker cannot encrypt the operating system volume with the USB boot key. This may be due to certain BIOS mode settings.

We hope these solutions have helped you solve your Bitlocker encryption problems.

If you have any other tips or suggestions, feel free to share them in the comments section below.

This source has been very much helpful in doing our research. Read more about this drive cannot be encrypted bitlocker and let us know what you think.

Frequently Asked Questions

How do I fix BitLocker drive encryption?

Fixing BitLocker Drive Encryption Error can be a bit tricky, but the steps listed below will walk you through the process. Before you begin, make sure that you’ve turned off the BitLocker Drive Encryption service. If you’re unfamiliar with the process, you might want to refer to the manual. The guide requires you to use an elevated Command Prompt. The BitLocker drive encryption feature is built into Windows and is very difficult to lose. However, it is quite possible to lose data when you forget the password. For example, if you forget the password, it is possible to access the volumes via BitLocker Repair Tool. You can run the BitLocker Repair Tool in Windows 7. BitLocker Repair Tool is a command-line tool used to repair volumes with BitLocker enabled. The BitLocker Repair Tool only fixes volumes without a TPM. If you have lost your password, you must turn on BitLocker with a recovery key orovery password.

How do I fix BitLocker Drive Encryption failed to recover an abruptly terminated conversion?

Microsoft’s BitLocker Drive Encryption secures your computer’s hard disk drive against unauthorized access. When you attempt to encrypt a drive, if the process is unsuccessful you may receive a BitLocker Drive Encryption failed to recover an abruptly terminated conversion error message. This can happen because of many reasons such as an unstable system, faulty hard drive, or storage device. Fixing this error is not difficult. Here are five steps which I found from a blog to repair this error. If you have been using BitLocker Drive Encryption to encrypt your hard drive and you have lost your recovery key, you may be stuck with an encrypted drive that you can’t access. While BitLocker can help keep your data secure, you may also find yourself out of luck if you don’t have the keys to gain access to your files. There is no one answer for every case, but there are a few things you can try to resolve this issue. You can try these things first:

Why my BitLocker is not working?

The drive is encrypted using Microsoft’s BitLocker, which has the ability to encrypt whole drives using a combination of symmetric and asymmetric encryption, using either a user-supplied password or a 48-character recovery key. The latter is stored on a Trusted Platform Module (TPM) that can be used to unlock the drive if the user forgets the key. The most common cause of this is that the TPM is not enabled, or has been disabled. In this case, the drive will not be encrypted, and will be left in a vulnerable state. A peculiar bitlocker drive encryption error has popped up on the internet, and it’s not clear how widespread it is. The issue seems to be affecting Windows 8 users who have used the “BitLocker” tool to encrypt their drives. (If you’re not familiar with the tool, it’s a highly secure way of encrypting a drive to protect its contents against hackers.) The problem is that the tool doesn’t appear to be working correctly, and some Windows 8 users are reporting that their drives won’t decrypt properly.

Related Tags:

bitlocker could not be enabled pop upbitlocker not working windows 10fve_e_system_volumethe media in the drive may have changedbitlocker greyed out windows 10how to enable bitlocker in bios,People also search for,Feedback,bitlocker access denied rdpbitlocker not workingthe hidden drive cannot be encryptedbitlocker vssbitlocker 0x80070005bitlocker drive encryption not responding,bitlocker not workingprotectkeywithtpm' failed 2150694984bitlocker drive encryption not responding,bitlocker tpm error windows 10bitlocker errorbitlocker error code: 0x80072f9asystem guard secure launcherror 80284001error: an error occurred (code 0x8031002c),bitlocker password instead of pindisable bitlocker password on bootbitlocker usb not asking for passwordbitlocker without tpm disadvantagesbitlocker not detecting usbbitlocker not asking for pin during setup,0x803100010x80290107the hidden drive cannot be encryptedwindows 10 bitlocker usbbitlocker not workingbitlocker drive encryption not responding,bitlocker not working windows 10bitlocker password not workingbitlocker to gomanage-bde,Privacy settings,How Search works,bitlocker drive encryption error,bitlocker drive encryption cannot be enabled on the operating system drive,bitlocker drive encryption error wizard initialization has failed,this drive cannot be encrypted bitlocker,bitlocker error windows 10,the drive cannot be encrypted because it contains system boot information usb,bitlocker could not be enabled drive cannot be unlocked automatically,failed to encrypt c bitlocker could not encrypt one or more drives on this computer